I tried using a Zojirushi futon dryer `` Smart Dry RF-EA20 '' that can make the futon soft and fluffy just by inserting
There are also cold seasons when the futon does not fluff even if you hang it outside, or days when the bad weather continues so that the futon does not dry and you need to sleep on a damp futon. With Zojirushi's futon dryer ' Smart Dry RF-EA20 ', it is easy to make futon soft and fluffy, so I actually used it.
Futon dryer RF-EA type | Product information | Zojirushi
This is 'Smart Dry RF-EA20'
The size is 28cm in width x 13cm in depth x 35cm in height. The weight is 4.1kg.
The nozzle is mounted on the upper part of the main unit in a folded state.
The angle of the outlet can be adjusted up and down according to what you want to dry.
The maximum angle is up to the point where the main body and the nozzle are perpendicular.
The outlet looks like this. Warm air comes out from here and warms the futon.
The front panel is the operation panel.
Insert the power cable into the outlet and press the power button to start up the main unit.
The operating mode that is selected is indicated by the red lamp.
You can check how long the vehicle will run in the selected mode by checking the time.
In addition to 'warm-up' which warms futon in cold season, 'drying' to dry futon efficiently is installed. In drying, there are three courses: `` standard '' of the Omakase course, `` blasting finish '' for summer that blows after the standard to lower the temperature of the futon, and `` anti-mite '' that eliminates mites in the futon There is.
In 'manual operation', it is possible to heat the futon for any time by specifying two types of temperature, 'hot air' and 'blowing'.
In manual mode, the operation time can be selected from 5 minutes to 180 minutes.
A 'code basket' for storing cords is also included with the main unit.
It looks like this when attached to the side of the main unit. When you do not use the main body, you can store the cords collectively.
So, actually try using it. First, fully open the nozzle and place the body on the mattress.
Put a futon over the nozzle ...
Hold the end of the futon firmly so that air does not leak from the gap between the main body and the futon. In addition, this time, the duvet is overlaid on the duvet.
In addition, 'futon detection sensor' is carried in the front of the body.
If the bedding hangs not only on the nozzle but also on the main unit, the operation of the main unit will stop with a warning sound 'beep'. If the futon is hung up to the sensor part, if a large gap is created between the main body and the futon, the warm air will escape and the futon will not be able to be heated efficiently, so the sensor will warn you.
After that, just press the power button, select the course and press 'Start'. This time, we started operation on the 'standard' course in the 'dry' mode.
The operation sound is like a small dryer. If you concentrate on something, the volume will not be noticeable, but it may not be quiet.
During use, you will feel a little hot air from the futon. If you use it in summer, it seems better to drive while you are out.
When using the
After the operation, touch the futon and measure the temperature by hand.
When the temperature is measured with the FLIR i3, the range where warm air can reach directly from the outlet is just under 50 degrees. The range where the warm air did not reach was just under 40 degrees.
The comforter is just under 35 degrees.
It was not warm up to the end opposite to the one where the Smart Dry was placed, but it may be because the mattress was not hanging at this position. The area where the mattress was hung seems to have warmed to 35 degrees or more.
The comforter is not only warm when you touch it, but also has a soft, plump texture with wrinkles. The function of warming is also attractive in the cold season, but the 'drying' function is attractive in the rainy season when you can't dry the futon outside even though you are sullen.
Smart Dry can adjust the angle of the outlet, so it is possible to dry the pillow. However, be careful as beads and pillows with low or high resilience will be denatured by heat.
Dry the hanging clothes.
Shoes can also be dried. When drying heat-sensitive items such as leather products, a 'blowing' course that does not use a heater is convenient.
There is a handle on the back of the main unit, so you can easily carry it without worrying about the weight of about 4 kg.
The width was 13cm, so it could be stored in a small space.
There are various types of futon dryers, but the appeal of 'Smart Dry RF-EA20' is 'easy to use'. The design is attractive because it can be used quickly by inserting a nozzle into the futon that is laid, and it can be easily carried and stored. It is recommended for those who do not like the cold futon in winter and those who tend to neglect washing the futon.
At the time of writing the article, Zojirushi 'Smart Dry RF-EA20' was available for purchase at Amazon.co.jp for 11,190 yen.
Related Posts:
