I tried to expand the bookshelf with "LABRICO" that can create a wall shelf without damaging the walls and ceiling

When living in a rental house, storage space is insufficient! It tends to be annoyed by the serious problem of. You can set a bookshelf, storage rack, TV etc on the wall with a stapler without damaging the wall "Wall beautyThere is also an item called, but I want a bigger storage shelf ... ... It seems to be useful when saying "LavlikoI found an item called "I tried using it." Because she can make a shelf with a wall in the manner of a brace bar it means that it will not hurt the ceiling and the wall.

LABRICO Renovation / Lavliko Official Brand Site
http://www.heianshindo.co.jp/labrico/

Even if you buy a book, there is a limit to the storage space in the living alone, you will buy and sell it again, but still the book you are collecting is what you want to keep, the density of the bookshelf gradually increases thing. I thought that it should be expanded bookrooms soon .... When I looked through the thought, I found "LABRICO" that can make shelves without damaging the ceiling and walls, so I bought it.


Lavliko purchased two "2 × 4 adjusters", "2 × 4 shelve receiving single" and "2 × 4 joints" each.


The main thing is 2 x 4 adjusters. As shown in the picture of the package, it is an item that plays a role like a stick to the ceiling and the floor by wearing it on the wood.


Two types, the upper cap attached to the ceiling side of the wood and the lower cap attached to the floor, are in the inside.


To use the 2 x 4 adjuster, you must first measure the height from the floor to the ceiling correctly. In the photograph, we are placing measures on places where there is nothing for shooting, but in the actual measurements it is correct to measure the height, such as the corner of the room, where the measure is definitely perpendicular to the floor Recommended. Basically, the length of wood to be purchased is the measured length minus 95 mm which is the size of the adjuster.


However, this time we use a 2 × 4 joint that connects two trees to make a long one pillar, so the length subtracting the width of the joint, 26 mm, is the total length of the pillars when connecting the timber .


Looking at the back of the package, you can see what kind of item the joint is. When attached to the edges and ends of two woods, it is a mechanism that can make one long pillar in the manner of a group tree. For example, if the floor-to-ceiling is 2 meters, the wood to be purchased will be "(200-9.5-2.6) ÷ 2" and two of 93.95 cm.


So I grasp the wood to be purchased and went to the home center.


What you can use Raburiko you purchased this time is said to be "2 × 4 material". The 2 × 4 material is called because the thickness of the wood entrance is 2 × 4 inches, but in fact it changes in size at the stage of drying and it becomes about 1.5 × 3.5 inches (about 3.8 × 8.9 cm) in the actual size . In the shop I bought, 2 x 4 material of 1.82 m in length was sold for 348 yen per one.


So purchase at the cash register ... ...


I asked the shop people to cut.


I want you to cut it gently with this huge machine.


When shop clerk tells the length of the timber you want, all the work will be done by the shop clerk, so it is very lucky that you do not have to do it from where you start cutting wood by yourself. The cutting work ended crisply in about 5 minutes.


That's why I bought 2 pieces of 4 pieces this time. It is two 120 cm wood to make two shelves and four wood to make two pillars.


The thickness is like this.


I could use wood as it is, but I thought that I want to make it a vintage atmosphere ~Bry waxI will decide to process with.


It opens the lid and looks like this. Since the raw material of Bra Wax is beeswax and carnauba plants, it is not liquid like a varnish but it is semi-solid and sticky.


First of all, we will apply a file to the wood to smooth the surface.


Paint Blywax on 2 × 4 material ......


Brush and polish with brush and cloth to polish. Because there was not a nice cloth, socks were substituted. For detailed usageAlso from this movieYou can check.


I was able to process it to a vintage atmosphere with a nice touch.


So I will actually use Raburiko. First of all, it is used from a joint that connects two timber to one.


In the box there were two pieces of joints, instructions, screws wrapped in blue vinyl.


There are 8 screws in all.


It is easy to use, first cover the joint part on one end of the 2 x 4 material for the pillar.


There are holes in the four corners like this in the joint parts.


Electric drivers appeared here.


I will screw in the screws. Depending on the location, it may be hard for wood to be hardened and screws are hard to enter, but basically it can be screwed even without a pilot hole.


After fixing the joint on one end of the two pieces of wood, slide the joints in the manner of a group tree ... ...


I just snapped in.


The completed pillar is like this. Since it is only in the state where the plastic parts are slid, it is slightly worried that it is a little grasping and "will it be okay?", But it will be a little uneasy, but since it will eventually push in the vertical direction, there is no problem.


Next, I will use "2 x 4 Racketar Single".


In the box there are two shelves and two screws and eight screws.


This applies to the edge of the timber used as a shelf with the following feeling ......


I will screw the screw.


It is like this when passing wood with shelves received at both ends through two pillars.


Furthermore, fix the wooden parts of the racking-receiving parts and the pillars with screws.


It gradually became like a shelf.


It is the main 2 × 4 adjuster that appears here. We will install on both ends of the wood that becomes the pillar. The adjuster has a soft material about 2 mm attached to the floor and the ceiling, so that it does not hurt the floor and ceiling when stretched. Attach the bottom cap ......


Next, install the upper cap. There is nothing special about screws etc, just cover it.


Carry this on the wall ... ...


I will adjust the upper cap.


The upper cap looks like this. At first there is plenty of room, the ceiling is not in contact with the ceiling cap.


But as I turn around the jacks ... ...


The heaven cap is firmly pressed against the ceiling, the pillars are stretched by the ceiling and the floor.


Once both the left and right pillars are stretched and fixed with ceiling and floor ......


I will arrange the Janken-chan books.


A book shelf is completed like this.


Of course, since it is in the state of a brace bar, it will collapse as long as you pull the shelf, but as it is used as a bookshelf, there is a sense of stability in the amount that is weighted from the top to the bottom.


It does not even grab the joint.


Since load capacity is 30 kg per shelf board, it seems to be enough to use as a bookshelf. Please note that the shelf board is up to 120 cm and it is up to 4 tiers per shelf.


Since the width of the shelf is 8.9 cm, which is the width of the wood, the edge comes out a bit if it is a B6 size comic, but it will not fall down as the wall will be substituted for the backboard.


When it is a book of a slightly larger size called 20.8 × 14.8 cm, it jumps out as the following feeling. There is also a voice that the sense of stability disappears when the load is applied too much in front of the shelf because it is a brace rod type, so if you want to store a larger size book, it was better to set it slightly away from the wall.


As a similar itemDearwallThere are, but for the DiaWall, the adjustment of the length of the pillar is up to 4 mm with the spacer and the LABRICO is up to 18 mm with the jack, so if the LABRICO is easier to adjust ... ...? One reason why I thought about picking Lavliko. Also, while the Deer Wall is of the type to fix with a spring, since Rabriko is a procedure of a stick rod as described above, one reason is that the fixation force seems to be strong, but if it is intended for a decorative shelf not putting heavy objects on it There may be a deal wall. Both designs are different, so it seems good to choose with design emphasis.

For Raburiko's 2 × 4 adjuster, the load capacity per pillar is 20 kg, and when using a joint it is 10 kg. When using two pillars like this time, the load capacity per shelf board is 30 kg, which is the same even if you use a joint. Notice that the shelf board is up to 120 cm long, up to 4 stages.

According to the editorial staff who used a deerwall as a bicycle holder in the state of a single pillar, it will be unstable if the weight in the forward direction is applied. Rakuten's review includes "Fell downBecause there is also the content saying that it is not heavy in front of the shelf, it is better to design a shelf that weighs vertically against the floor.

Raburiko has 2 × 4 adjusters 880 yen including tax, shelving single is 734 yen including tax, joint is about 824 yen including tax,RakutenYaAmazonAvailable for purchase. If it is this bookshelf it was 6964 yen in total with Labrico and wood.