100% waterproof and shock-resistant bag "PRO DRYBAG 45L" which does not wet the contents of the bag even if it is submerged at a water depth of 50 m

Among the elements required for the bag is a bag pursued to the ultimate "being robust"PRO DRYBAG"is.Thermoplastic polyurethane elastomer(TPU), it is resistant to shocks, boasts the waterproof performance of IPX 8, has become a bag that considered even the ease of portability, and it is becoming a bag that seems to be pretty usable for sports and active people.

PRO DRYBAG 45L - 100% Waterproof (50 m / 164 ft) by SUBTECH SPORTS - Kickstarter

For those who do sports and active people, "rugged bag" is a necessity. PRO DRYBAG is made by making bags that protect the contents wherever they are brought, such as sand and water.

The size of PRO DRYBAG is 60 cm × 30 cm × 30 cm and the content quantity is 45 L. It boasts the waterproof performance of IPX 8, uses impact resistance technology, the main fastener is performing pressure resistance test, and furthermore it does not receive the inside air, so even if you carry it in the water, the contents will not collapse under hydraulic pressure . Material of the bagThermoplastic polyurethane elastomerIn, adopting a smart pocket system, it is designed based on ergonomics to carry as backpack.

If it is as durable as PRO DRYBAG, you can take it anywhere in the amphry.

Even if it gets soaked, it is ok.

I can take it to the water.

When used as a backpack like this.

I can withstand extreme sports.

This is the rough sketch when I started making products.

Materials were examined many times since the sketch was done, and the performance necessary to protect key points and contents in bag making was analyzed.

The zipper200 N / cmTo withstand.

Adjust the size and length of the small parts.

It adopts a smart pocket system, and the inside of the bag also comes with pockets for ease of use.

This is the outside strap.

When you open the zipper with the contents in it, it looks like this.

This is how the bag is seen from above. The fastener is not parallel to the long side of the bag, but it is attached in a form traversing from the corner to the corner.

Looking from the side it looks like the following.

Note that PRO DRYBAG, which is currently seeking investment at the Cloud Funding platform, is planning to upgrade its functions according to how much funds were collected. For example, the whole bag is black, but by using a material that reflects light in the yellow part of the logo you can make it easier to find where the bag is and where the person carrying the bag is.

If you use a super lightweight nylon mesh, you can lighter weight of 748 g as it is toughness.

If you gather $ 75,000 (about 8.90 million yen) you can withstand from 71 ℃ to minus 40 ℃ and you can create a bag that can inflate like a balloon.

Because it does not escape the air inside, it can be used as a flotation.

Also, if the inner side of the bag is made of TPU material, even if it is scratched with a sharp object it will never be torn. In other words, if all the functions can be installed, it will become a tough bag with four of "waterproof", "shock resistance", "visibility" and "tear-proof".

PRO DRYBAG gathered $ 44,000 (about 5.2 million yen) at the time of article writing where the target amount is 15,000 dollars (about 1.8 million yen), and "use the material that reflects light to the yellow part of the logo" The stretch goal of 30,000 dollars (about 3.6 million yen) has already been attained, and the next point is aiming for a stretch goal of $ 75,000 (about 8.90 million yen). With a contribution of 129 dollars (about 15,000 yen), you can get one PRO DRYBAG, and the number of bags you get when you increase the investment amount is increasing, ships correspond to the whole world, shipping fee is free.

The deadline is Japan time and it is 22:00 on December 19, 2014.

PRO DRYBAG 45L - 100% Waterproof (50 m / 164 ft) by SUBTECH SPORTS - Kickstarter

in Design, Posted by darkhorse_log