Speeding up the whole process of "Porsche 911 GT 3 RS" boasting the highest reproducibility in LEGO history makes this

Among the block toys "LEGO (Lego)", in the "LEGO technique" series for advanced users who reproduce small parts using small parts and gears (gears) and shafts,Porsche 911 GT 3 RS"Has appeared. YouTube has released a state of making and assembling finely detailed parts that seems to be a crazy moment.

Lego Technic 42056 Porsche 911 GT 3 RS - Lego Speed ​​build - YouTube


"Lego Technique Porsche 911 GT 3 RS" is in a black box.


Opened.


Opening the box ......


It is divided into small boxes with numbers.


The manual is this thickness.


Inside the history of Porsche 911 ......


Up to parts list.


There seems to be a sticker.


Lego technique Porsche 911 GT3 RS has "2704" parts count. The price is 299 dollars (about 31,000 yen)


First off from the 1st box. The package shows what seems to be an engine in the package.


I will put out the block from the box.


We will assemble small blocks and gears.


The gear part is this level.


This part ......


Pattern around handle.


The driver's seat is like this.


Around the front suspension is also completed.


Yellow Brembo caliper etc are finely reproduced.


We combined the front suspension.


Subsequently, rear suspension.


Rear suspension is also installed. Both front and rear are built to actually function as a suspension.


Hold the car upside down, gray engine mount mounted. It is time to move around the engine at last.


Of course the horizontally opposed crankcase.


A yellow piston was attached to the crankshaft.


Flat 6 was assembled.


Attach the engine to the rear.


GT3 RS 4.0 sticker pasted ......


Completed the engine by installing it on top of the engine.


Then a box of No. 2.


The parts look like this.


It seems to be making a monocoque frame.


Crafts such as crossed roll bars are detailed ......


To the chassis already made ......


I put the frame from the top, and the monocoque frame was completed.


Combine chassis and frame.


Bucket seat is also assembled with small parts.


Both driver's and passenger's seats are wearing.


The third box.


Because it is an exterior part, it has a lot of orange parts.


We will also assemble the wheel arch etc. finely with multiple parts.


Reproduce the cushioning material inside the rear bumper.


The tail lamp is also a combination of fine parts.


Attached engine hood. It seems like a 911 rear has started.


The trunk hood is also assembled with divided parts.


Fitted on the front.


Since GT 3 RS is a sticker specification rather than a crest, the degree of reproduction is 100%.


The roof part is full of all the split parts. I feel that I am committed to being "Lego" not a plastic model.


The 4th box.


The front meter points at 325 km / h with over 8000 revolutions.


Attached with the dashboard.


Black jagged rectangular parallele ...


It was a radiator.


On the front fender, reproduce the air duct with a sticker.


Front lights were completed by laminating transparent parts.


Attached to the left front of the car body.


Also equipped with turn signal lights and front bumper.


Then the door.


Of course movable type.


It gradually became 911-like appearance.


Reproduced with a sticker to the engine cover.


Fitted to hide the flat 6.


What made a combination of small parts ......


It was a rear wing.


It also approaches completion with wearing exterior parts on the right side of the car body.


The arch shaped windshield is reproduced with rubber parts.


A pillar and C pillar We are using rounded parts.



A distinctive rear silhouette of 911 is completed.


The last part is the wheel part.


Fit the wheel in the tire ......


Finally, "Lego Technique Porsche 911 GT 3 RS" is completed if it is attached to 4 wheels ......



Thinking like that, it's like a small bag.


It seems to stick to how to reproduce Porsche genuine suitcase.


Complete it if you put the suitcase and tighten the trunk hood.


I made the Porsche 911 GT 3 RS brilliantly with over 4000 parts.


By the way the rear spoiler is mobile.



Opening the engine hood ......


You can see the logo of "GT3 RS 4.0".


Opening the trunk hood ......


Enter suitcase.


The door will also be opened and closed.



Driver's seat built in.


How, after turning off the steering, the tire moved.


Rear suspension ... ....


Front suspension is also movable.


"Lego Technique Porsche 911 GT 3 RS", which has over 4000 parts and high reproducibility,Porsche AGIt was born by joint development with Lego.




"Lego Technique Porsche 911 GT 3 RS" which is not exaggeration to say the best deki in the history of Lego technique is on sale for $ 299 (about 31,000 yen) in the United States. It will be released in 299 euros (about 35,000 yen) and 249 pounds (about 37,000 yen) in other areas. It is scheduled to be released in Japan in October 2016, and the price is undecided at the time of article creation.

Porsche 911 GT 3 RS - Product Information - LEGO.com
http://www.lego.com/ja-jp/technic/products/porsche-911-gt3-rs-42056